Инструкция для Sony ICF-C1IPMK2

3-873-060-

36

(1)

FM/AM Clock Radio 

ICF-C1iPMK2

Operating Instructions

©2008   Sony Corporation     Printed in China

Dream Machine is a trademark of Sony Corporation.

No Power No Problem is a trademark of Sony Corporation.



FM wire aerial

AC power cord



There is a tactile dot on the VOLUME +, 



/



 and PRESET TUNING 3 button. 

There is a tactile dot on the VOL +, 



/



, 



 and PRESET + button.



CR2032







CR2025

WARNING

To reduce the risk of fire or electric shock, do not 

expose this apparatus to rain or moisture.

To reduce the risk of fire, do not cover the ventilation 

of the apparatus with newspapers, tablecloths, 

curtains, etc. And do not place lighted candles on the 

apparatus.

The apparatus shall not be exposed to dripping or 

splashing and no objects filled with liquids, such as 

vases, shall be placed on the apparatus.
Do not install the appliance in a confined space, such 

as a bookcase or built-in cabinet.
As the main plug is used to disconnect the unit from 

the mains, connect the unit to an easily accessible AC 

outlet. Should you notice an abnormality in the unit, 

disconnect the main plug from the AC outlet 

immediately.

Notice for customers: the following information 

is only applicable to equipment sold in countries 

applying EU directives

The manufacturer of this product is Sony Corporation, 

1-7-1 Konan, Minato-ku, Tokyo, 108-0075 Japan. The 

Authorized Representative for EMC and product 

safety is Sony Deutschland GmbH, Hedelfinger Strasse 

61, 70327 Stuttgart, Germany. For any service or 

guarantee matters, please refer to the addresses given 

in separate service or guarantee documents.

WARNING

 

Danger of explosion if battery is incorrectly 

replaced. Replace only with the same or equivalent 

type. 

 

Replace the battery for the clock backup with a Sony 

CR2032 lithium battery, and the battery for the 

remote commander with a Sony CR2025 lithium 

battery. Use of another battery may present a risk of 

fire or explosion. 

 

Battery may explode if mistreated. Do not recharge, 

disassemble or dispose of in fire.

 

Do not expose the batteries (battery pack or 

batteries installed) to excessive heat such as 

sunshine, fire or the like for a long time.

 

Dispose of used battery promptly. Keep away from 

children.

Precautions

 

Operate the unit on the power source specified in 

“Specifications”.

 

To disconnect the power cord (mains lead), pull it 

out by the plug, not the cord.

 

The unit is not disconnected from the AC power 

source (mains) as long as it is connected to the wall 

outlet, even if the unit itself has been turned off.

 

Allow adequate air circulation to prevent internal 

heat build-up. Do not place the unit on a surface (a 

rug, blanket, etc.) or near materials (a curtain) that 

might block the ventilation holes.

 

Should any solid object or liquid fall into the unit, 

unplug the unit and have it checked by a qualified 

personnel before operating it any further.

 

To clean the casing, use a soft cloth dampened with 

a mild detergent solution.

 

Do not connect the aerial lead to the external aerial.

 

To reduce the risk of fire, do not cover the 

ventilation of the apparatus with newspapers, 

tablecloths, curtains, etc. And do not place lighted 

candles on the apparatus.

NOTES ON LITHIUM BATTERY

 

Wipe the battery with a dry cloth to assure a good 

contact.

 

Be sure to observe the correct polarity when 

installing the battery.

 

Do not hold the battery with metallic tweezers, 

otherwise a short-circuit may occur.

Disposal of Old Electrical & 

Electronic Equipment 

(Applicable in the European 

Union and other European 

countries with separate 

collection systems)

This symbol on the product or on its packaging 

indicates that this product shall not be treated as 

household waste. Instead it shall be handed over to the 

applicable collection point for the recycling of 

electrical and electronic equipment. By ensuring this 

product is disposed of correctly, you will help prevent 

potential negative consequences for the environment 

and human health, which could otherwise be caused 

by inappropriate waste handling of this product. The 

recycling of materials will help to conserve natural 

resources. For more detailed information about 

recycling of this product, please contact your local 

Civic Office, your household waste disposal service or 

the shop where you purchased the product.

Connecting the aerial

To connect the AM loop aerial

The shape and the length of the aerial is designed to 

receive AM signals. Do not dismantle or roll up the 

aerial.

1 

Remove only the loop part from the plastic 

stand.

2 

Set up the AM loop aerial.

3 

Connect the cords to the AM aerial 

terminals.

The cords (A and B) can be connected to either 

terminal.

Insert the cord while 

pushing down the 

terminal clamp.

4 

Make sure the AM loop aerial is connected 

firmly by pulling softly.

Adjusting the AM loop aerial

Find a place and an orientation that provide good 

reception.

 

Do not place the AM loop aerial near the unit or 

other AV equipment, as noise may result.

 

If you use an external polarized AM aerial, be sure 

to connect the ground cord to the 



 terminal. The 

supplied AM aerial cord has no polarity.

Tip

Adjust the direction of the AM loop aerial for best AM 

broadcast sound.

About the backup 

battery

To keep good time, as a backup power source, this unit 

has one CR2032 battery inside of the unit in addition 

to the house current.

The battery keeps the clock and the alarm operating in 

the event of a power interruption.

Note that the backlight will not light up during a 

power interruption.

Note for customers in the UK

The clock is preset at the factory, and its memory is 

powered by the preinstalled Sony CR2032 battery. If 

the “AM 12:00” appears in the display when the unit is 

connected to AC outlet for the first time, the battery 

may be weak. In this case, consult a Sony dealer. The 

preinstalled CR2032 battery is considered part of the 

product, and is covered by the warranty. 

You are required to show “Note for customers in the 

UK” (in this instruction) to a Sony dealer in order to 

validate the warranty for this product.

Knowing when to replace the 

battery

If the battery runs out during the interruption, the 

current time and alarm functions will be initialized.

Replace the battery with a Sony CR2032 lithium 

battery. Use of another battery may present a risk of 

fire or explosion.

Replacing the backup battery

1 

Keep the AC plug connected to the AC 

outlet, remove the screw that secures the 

battery compartment at the bottom of the 

unit using a screwdriver, and remove the 

battery compartment. (See Fig. 



-



)

2 

Insert a new battery in the battery 

compartment with the 



 side facing up.

To remove the battery from the battery 

compartment, push it out from the side marked 

PUSH. (See Fig. 



-



)

Disposal of waste batteries 

(applicable in the European 

Union and other European 

countries with separate 

collection systems)

This symbol on the battery or on the packaging 

indicates that the battery provided with this product 

shall not be treated as household waste.

On certain batteries this symbol might be used in 

combination with a chemical symbol. The chemical 

symbols for mercury (Hg) or lead (Pb) are added if the 

battery contains more than 0.0005% mercury or 

0.004% lead.

By ensuring these batteries are disposed of correctly, 

you will help prevent potentially negative 

consequences for the environment and human health 

which could otherwise be caused by inappropriate 

waste handling of the battery. The recycling of the 

materials will help to conserve natural resources.
In case of products that for safety, performance or data 

integrity reasons require a permanent connection with 

an incorporated battery, this battery should be 

replaced by qualified service staff only.

To ensure that the battery will be treated properly, 

hand over the product at end-of-life to the applicable 

collection point for the recycling of electrical and 

electronic equipment.
For all other batteries, please view the section on how 

to remove the battery from the product safely. Hand 

the battery over to the applicable collection point for 

the recycling of waste batteries.
For more detailed information about recycling of this 

product or battery, please contact your local Civic 

Office, your household waste disposal service or the 

shop where you purchased the product.

If you have any questions or problems 

concerning your unit, please consult your nearest 

Sony dealer.

Features

 

Dual alarm FM/AM Clock radio with iPod dock. 

 

Various type of alarms- iPod, radio and buzzer.

 

Automatic time set — When you plug the clock in 

for the first time, the current time will be shown in 

the display.

 

Automatic Daylight Saving Time/Summer time 

adjustment.

 

CLOCK button to display month, day and year. 

 

Brightness control (High/Middle/Low).

 

No Power No Problem™ alarm system to keep the 

clock and the alarm operating during a power 

interruption with a CR2032 battery installed.

3 

Insert the battery compartment back into 

the unit and secure it with the screw.  

(See Fig. 



-



)

Note

When you replace the battery, keep the AC plug 

connected to a wall outlet. Otherwise, current time 

and alarms will be initialized if the replacement is not 

completed within around one minute. 

If the time in the display is 

incorrect after the battery is 

changed (RESET)

Push the Reset switch with the pointed device. The 

Reset switch is in the small hole located in the battery 

compartment.

Notes

 

You cannot reset unless the lithium battery is 

installed.

 

Set the clock again after the unit is reset.

Battery Warning

When the unit will be left unplugged for a long time, 

remove the battery to avoid undue battery discharge 

and damage to the unit from battery leakage.

Preparing the remote 

commander

Before using the card remote commander for the first 

time, remove the insulation film. (See Fig. 



-



)

When to replace the battery 

With normal use, the battery (CR2025) should last for 

about six months. When the remote commander no 

longer operates the unit, replace the battery with new 

ones. (See Fig. 



-



)

Notes

 

Do not charge the battery.

 

When you are not going to use the remote 

commander for a long time, remove the battery to 

avoid any damage caused by leakage and corrosion.



